When a commercial boiler fails or does not operate properly, it can cause a significant disruption to the facility it is used to heat. For example, in an office environment, it is important that staff members have adequate heat, and the same is true for any building requiring heat and hot water.
Seeking the help of a qualified Paris 13 heating engineer is usually the best solution if you discover a problem with your commercial boiler, but if you're only experiencing minor issues, you may be able to fix it yourself. In this blog, we explain some of the common causes of boiler problems and how to avoid or solve them, and look specifically at how to repair a boiler leak.
How to repair a broken boiler
Commercial boilers can experience a variety of problems, including the following...
Low system pressure
If your commercial boiler shows low system pressure, it could lead to a complete breakdown. To prevent this from happening, perform regular checks on the pressure gauge, and if you see any significant changes, seek help from a qualified engineer.
Poor heat production
Often caused by an internal blockage of debris, a reduction in heat output is unlikely to cause catastrophic problems, but it will reduce the effectiveness and efficiency of your boiler. You must ensure that your boiler is cleaned regularly to prevent a build-up of debris from affecting the efficiency of your boiler.
Strange sounds
Commercial boilers often make noise, and in many cases there is nothing to worry about. However, if they make a hissing or popping sound, there could be a potentially serious problem. This could be due to low water pressure or a buildup of limescale. To see what's behind the problem, you can check that the air intake, exhaust, pressure and piping are all in good condition. If not, they will need to be replaced.
Unexplained stop
Whether your commercial boiler is showing odd water pressure readings, the thermostat is faulty or simply not working properly, the best course of action is to seek the advice of a qualified heating engineer. A number of problems can cause your boiler to stop working, so it can be difficult to know what the appropriate solution is. As such, it would be advisable to seek expert help.
How to repair a leaking boiler
A common problem with commercial boilers, leaks can be as minor as a few insignificant drops of water or severe enough to cause serious damage to your system. The key is to identify a leak early and find an effective solution to prevent further damage. To do this, you should check your heating system regularly for leaks. For added safety, you can even install a sensor that will alert you if the bottom of the boiler contains water.
There are many reasons why your boiler may be leaking. For example, a buildup of pressure could have caused the pressure relief valve to leak. water leakage. To solve this problem, you may need to close the valve, descale it or bleed the entire boiler. If the temperature and quality of the water entering the commercial boiler are not properly regulated, the problem could be thermal fatigue. If the water entering the boiler is too cold, thermal shock can lead to cracks in the system. If the water is too hot, cracks may start to appear on the boiler, eventually leading to total failure.
Another potential cause of leakage could be rust or corrosion. In older commercial boilers, this is perfectly natural and an annual service should indicate whether the boiler needs to be replaced. However, poor water quality can also cause damage to the inside of the boiler. You should be able to spot this during routine maintenance by observing the condition of the pipes and other areas through which the water flows.
How to repair a leaking boiler pipe
When a pipe in your commercial boiler system begins to leak, it can cause significant damage and dangerous repercussions. While you may need to call in a qualified professional to look at the system or rent a temporary replacement boiler, there are a few tips that can help you prevent the leak from damaging the building it's in or putting anyone nearby in danger.
As a commercial boiler operator, you can repair a leaking pipe in:
- turn off the water supply
- turn off the boiler
- draining the remaining water from the system
- clean up the damage caused by the leak
- Identifying the leaking hose - If it is simply not installed properly, you may be able to tighten it in place. If it is easy to remove, replace it with the same size pipe. Or, if there is a clear leak but it cannot be removed, coat the leak with waterproof PTFE tape and contact a qualified engineer.
If your commercial boiler is damaged and you need a temporary replacement while it is being repaired or a permanent replacement is installed, Artisans Bruno provides the right solution with the name boiler maintenance Paris 13
